HLC8 LED LAMP (INTEGRATED DRIVER)

PREMIUM SERIES

Features

  • Integrated driver with high PFC
  • For direct replacement for conventional control gear circuit as per IEC 62776:2015
  • Rewiring and removal of magnetic ballast are not required
  • Ultra high efficient and durable control driver IC and Japanese electrolytic capacitors
  • Nichia LEDs with 50K hours life at L70, with IES LM-80-08 certified
  • High number of switching cycles
  • Aluminum PCB for better LED heat dissipation
  • Using segmenting LED binnings for narrower CCT range
  • System efficacy up to 180 lm/w
  • Aluminum heat sink with polycarbonate tube
  • Extremely break resistant
  • Complies with RoHS directive

Characteristics

Rated supply voltage 220-240 VAC ±10%
Supply frequency 50-60 Hz
Start time < 0.5 Sec
Lamp switching cycles >200,000
Ambient temperature (ta) -20 … +50°C
Driver efficiency up to 87%
Power factor ≥95%
THD <15%
Protection IP20
CRI >80
Beam angle 150°
Lumen maintenance (L70) >50K Hrs

%

Power Factor

%

THD

Years Warranty

Hours of LED Life

Lumen / Watt

LED Chips

The series incorporates best of best Nichia LEDs from Japan. The LEDs have the longest LED life and the best performance in the industry.

They are IES lM-80-2008 (Measuring Lumen Maintenance of LED Light Sources) certified for the best reliability and performance.

For eye safety, the LEDs are also IEC 62471:2008 (Photobiological Safety of Lamps and Lamp Systems) certificated.

LED Tube Dimensions

Model Diameter
(mm)
Length L
(mm)
HLC8-600 28 603
HLC8-900 28 908
HLC8-1200 28 1213
HLC8-1500 28 1513

CCG Retrofit Instructions (as per IEC 62776)

  1. Switch off electricity
  2. Rotate the conventional lamp
  3. Remove the conventional lamp
  4. Remove the starter
  5. Click the LED replacement starter into the starter holder
  6. Insert the LED lamp into the lampholder.
  7. Secure the position by turning the lamp by 90°
  8. Switch on electricity and check for lamp starting

Direct Wiring Instructions

  1. Rewiring must be done by qualified electricians only
  2. Switch off and disconnect electricity
  3. Remove the fluorescent lamp
  4. Remove power factor correction capacitor if installed
  5. Rewire the luminaire as shown in the circuit diagam
  6. Use LED replacement starter or a fuse of 250V 2A for protection
  7. Insert HLI T8 LED lamp
  8. Mark the luminaire to indicate replacement LED lamp type
  9. Never insert fluorescent lamp with rewired luminaire

Compliances

EN 62776:2015 Double-capped LED lamps designed to retrofit linear fluorescent lamps – Safety specifications

EN 62471:2008 Photobiological safety of lamps and lamp systems

EN 60155 Glow-starters for fluorescent lamps

EN 55015 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment

EN 61000-3-2 Electromagnetic compatibility (EMC). Limits. Limits for harmonic current emissions (equipment input current ≤ 16 A per phase)

EN 61000-3-3 Electromagnetic compatibility (EMC). Limits. Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection

EN 61547 Equipment for general lighting purposes. EMC immunity requirements

Ordering Information

Model Circuit
Power (W)
PF
(%)
THD
(%)
CCT
(K)
Lumen
(lm)
Efficacy
(lm/W)
Length
(L)
HLC8-600-7-830 7.0 ≥92 <15 3000 1100   603
HLC8-600-7-840 7.0 ≥95 <15 3000 1200   603
HLC8-600-7-865 7.0 ≥95 <15 3000 1200   603
HLC8-900-10-830 10.0 ≥95 <15 3000 1650   908
HLC8-900-10-840 10.0 ≥95 <15 4000 1800   908
HLC8-900-10-865 10.0 ≥95 <15 4000 1800   908
HLC8-1200-14-830 14.0 ≥95 <15 4000 2300   1213
HLC8-1200-14-840 14.0 ≥95 <15 4000 2500   1213
HLC8-1200-14-865 14.0 ≥95 <15 6500 2500   1213
HLC8-1500-20.5-830 20.5 ≥95 <15 6500 3400   1513
HLC8-1500-20.5-840 20.5 ≥95 <15 6500 3700   1513
HLC8-1500-20.5-865 20.5 ≥95 <15 6500 3700   1513