HLC8 LED LAMP (INTEGRATED DRIVER)

STANDARD SERIES

Features

  • Integrated driver with high PFC
  • For direct replacement for conventional control gear circuit as per IEC 62776:2014
  • Rewiring and removal of magnetic ballast are not required
  • Ultra high efficient and durable control driver IC and Japanese electrolytic capacitors
  • Everlight with 40K hours life at L70
  • High number of switching cycles
  • Aluminum PCB for better LED heat dissipation
  • Using segmenting LED binnings for narrower CCT range
  • System efficacy up to 150 lm/w
  • Aluminum heat sink with polycarbonate tube
  • Extremely break resistant
  • Complies with RoHS directive

Characteristics

Rated supply voltage 220-240 VAC ±10%
Supply frequency 50-60 Hz
Start time < 0.5 Sec
Lamp switching cycles >200,000
Ambient temperature (ta) -20 … +50°C
Driver efficiency up to 87%
Power factor ≥95%
THD <15%
Protection IP20
CRI >80
Beam angle 150°
Lumen maintenance (L70) >50K Hrs

%

Power Factor

%

THD

Years Warranty

Hours of LED Life

Lumen / Watt

LED Chips

Everlight LEDs are used for this series to achieve  high efficacy,  high CRI and price performance ratio.

They are IES lM-80-2008 (Measuring Lumen Maintenance of LED Light Sources) certified to sure the reliability and performance.

LED Tube Dimensions

Model Diameter
(mm)		 Length L
(mm)
HLC8-600 28 603
HLC8-900 28 908
HLC8-1200 28 1213
HLC8-1500 28 1513

CCG Retrofit Instructions (as per IEC 62776)

  1. Switch off electricity
  2. Rotate the conventional lamp
  3. Remove the conventional lamp
  4. Remove the starter
  5. Click the LED replacement starter into the starter holder
  6. Insert the LED lamp into the lampholder.
  7. Secure the position by turning the lamp by 90°
  8. Switch on electricity and check for lamp starting

Direct Wiring Instructions

  1. Rewiring must be done by qualified electricians only
  2. Switch off and disconnect electricity
  3. Remove the fluorescent lamp
  4. Remove power factor correction capacitor if installed
  5. Rewire the luminaire as shown in the circuit diagam
  6. Use LED replacement starter or a fuse of 250V 2A for protection
  7. Insert HLI T8 LED lamp
  8. Mark the luminaire to indicate replacement LED lamp type
  9. Never insert fluorescent lamp with rewired luminaire

Compliances

EN 62776:2015 Double-capped LED lamps designed to retrofit linear fluorescent lamps – Safety specifications

EN 62471:2008 Photobiological safety of lamps and lamp systems

EN 60155 Glow-starters for fluorescent lamps

EN 55015 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment

EN 61000-3-2 Electromagnetic compatibility (EMC). Limits. Limits for harmonic current emissions (equipment input current ≤ 16 A per phase)

EN 61000-3-3 Electromagnetic compatibility (EMC). Limits. Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection

EN 61547 Equipment for general lighting purposes. EMC immunity requirements

Ordering Information

Model Circuit
Power (W)		 PF
(%)		 THD
(%)		 CCT
(K)		 Lumen
(lm)		 Efficacy
(lm/W)		 Length
(L)
HLC8-600-8-830E 8.0 ≥92 <15 3000 1100   603
HLC8-600-8-840E 8.0 ≥95 <15 4000 1200   603
HLC8-600-8-865E 8.0 ≥95 <15 6500 1200   603
HLC8-900-12-830E 12.0 ≥95 <15 3000 1650   908
HLC8-900-12-840E 12.0 ≥95 <15 4000 1800   908
HLC8-900-12-865E 12.0 ≥95 <15 6500 1800   908
HLC8-1200-16-830E 16.0 ≥95 <15 3000 2300   1213
HLC8-1200-16-840E 16.0 ≥95 <15 4000 2500   1213
HLC8-1200-16-865E 16.0 ≥95 <15 6500 2500   1213
HLC8-1500-19.5-830E 19.5 ≥95 <15 3000 2850   1513
HLC8-1500-19.5-840E 19.5 ≥95 <15 4000 3100   1513
HLC8-1500-19.5-865E 19.5 ≥95 <15 6500 3100   1513
HLC8-1500-23-830E 23.0 ≥95 <15 3000 3400   1513
HLC8-1500-23-840E 23.0 ≥95 <15 4000 3700   1513
HLC8-1500-23-865E 23.0 ≥95 <15 6500 3700   1513